Turbidity Sensor Calibration Procedure at Instronline
Friday, September 14, 2018 IST
The turbidity method is based upon a comparison of intensity of light scattered by a sample under defined conditions with the intensity of light scattered by a standard reference suspension. A turbidimeter is a nephelometer with a visible light source for illuminating the sample and one or more photo-electric detectors placed ninety degrees to the path of the light source. Note: the below calibration procedure is for a turbidimeter which the sample is placed into a cuvette.
Some instruments will only accept one standard. For those instruments, the second, third, etc., standards will serve as check points.
Calibration Procedure:
1. Allow the calibration standards to equilibrate at the ambient temperature. The use of commercially available polymer primary standards (AMCO-AEPA-l) is preferred; however, the standards can be prepared using Formazin (read the warning on the label before use) according to the EPA analytical Method 180.1. Other standards may be used if they can be shown that they are equivalent to the previously mentioned standards.
2. If the standard cuvette is not sealed, rinse a cuvette with deionized water. Shake the cuvette to remove as much water as possible. Do not wipe dry the inside of the cuvette because lint from the wipe may remain in the cuvette. Add the standard to the cuvette.
3. Before performing the calibration procedure, make sure the cuvettes are not scratched and the outside surfaces are dry and free from fingerprints and dust. If the cuvette is scratched or dirty, discard or clean the cuvette respectively. Note: some . manufacturers require the cuvette to be orientated in the instrument in a particular direction for accurate reading.
4. Select a low value standard such as a zero or 0.02 NTU and calibrate according to manufacturer’s instructions. Note: a zero standard (approximately 0 NTU) can be prepared by passing distilled water through a 0.45 micron pore size membrane filter.
5. Select a high standard and calibrate according to manufacturer’s instructions or verify the calibration if instrument will not accept a second standard. In verifying, the instrument should read the standard value to within the specifications of the instrument. If the instrument has range of scales, check each range that will be used during the sampling event with a standard that falls within that range.
6. Record the calibration information on calibration log sheet.
Related Topics
Trending News & Articles
While the Uttarakhand High Court has asked to block 857 websites, the Ministry of Electronics and IT (Meity) found 30 portals without any pornographic content.
...
Recently posted . 64K views . 1 min read
The four boys as well as five school officials, including the director and principal, were arrested after the incident. The minors were presented before the Juvenil...
Recently posted . 10K views . 1 min read
Rahul was having an Italian passport and was carrying suitcase full of dollars. Some say it was about was it $2 million.
Rahul and his girl friend was th...
Recently posted . 9K views . 7 min read
True – Tr...
Recently posted . 8K views . 83 min read
More in Electronics & Gadgets
IndiGo Monsoon sale: In a bid to woo passengers this monsoon season, domestic airline IndiGo has come out with an using which customers can book flight tickets for ...
Recently posted. 1K views . 1 min read
OYO founder Ritesh Agarwal was just 18 when he came up with the idea. Within just a few years, OYO surpassed the valuation of India’s oldest hotel company.<...
Recently posted. 970 views . 1 min read
IRCTC has collaborated with Bueno Insta Pizza Private Limited (YESS PIZZA) and Owl Tech Private Limited (FRSHLY) for serving food from automatic vending courts wi...
Recently posted. 1K views . 1 min read
Recently posted . 1K views
Recently posted . 1K views
Recently posted . 2K views
Recently posted . 2K views
Recently posted . 3K views . 52 min read
Recently posted . 4K views . 126 min read
RBI has suggested use of external benchmarks such as the repo rate, 91-day Treasury bill yield or the 182-day Treasury bill yield produced by Financial Benchmarks...
Recently posted. 867 views . 1 min read
The incident took place on Sunday night.
Recently posted. 629 views . 0 min read